中国铸造

所属栏目：科技期刊热度：时间：

中国铸造 关注(): 期刊周期：季刊; 期刊级别：省级; 国内统一刊号：21-1498/TG; 国际标准刊号：1672-6421; 主办单位：沈阳铸造研究所; 主管单位：沈阳铸造研究所; 上一本期杂志：中南公路工程湖南省科学技术期刊; 下一本期杂志：中国铁路中文核心期刊

　　作为中国铸造业唯一一本英文版科技期刊，开设了“专题综述”、“科技研发”、“大学简介”、“铸件供应商”、“铸件及原辅材料价格”等栏目，及时详细地报道中国铸造领域的科研、生产、贸易及行业活动信息。《中国铸造》创刊虽仅3年，却已成为中国铸造业通往世界的桥梁和世界了解中国铸造业的窗口。

　　阅读推荐：中国铸造装备与技术

　　《中国铸造装备与技术》杂志是由中国科协主管，中国机械工程学会、中国机械装备(集团)总公司济南铸造锻压机械研究所主办的国家综合型科学技术刊物，1966年经中共中央宣传部批准创刊，当时的刊名是《铸造机械》。经过二十个春秋之后，于1986年更名为《中国铸机》，被广大读者誉为“知识的宝库，信息的源泉，交流的纽带，良师益友”。

　　中国铸造最新期刊目录

Drop-weight impact resistances of integrated forming aluminum foam sandwich double tubes

摘要：Aluminum foam filled tubes are good energy-absorbing structures. In this study, integrated forming aluminum foam sandwich double tubes(IFAFSDTs) were fabricated utilizing an improved melt foaming meth...

Effect of eutectic content on microstructure and mechanical properties of Al-Zn-Mg-Cu alloys

摘要：The 7xxx series aluminum alloys have emerged as a particularly promising class of lightweight structural materials. However, the inherent strength of these materials is primarily influenced by the con...

Tailoring microstructures and mechanical properties of cast Mg-Zn-Al-Mn alloys through alloying with Cu,Sn,and Y

摘要：Mechanical properties of cast Mg alloys remain insufficient for demanding applications. In this study, individual and combined effects of Cu, Sn, and Y additions on secondary phase characteristics and...

Effect of critical tempering on microstructure evolution, mechanical performance, and corrosion behavior of a cast multiphase stainless steel

摘要：A novel cast stainless steel featuring a multiphase microstructure and a nominal composition of Fe-13.5 Cr-2.6 Si-6.9 Ni-1.1 Cu-1.1 Mn-1.0 Mo-0.35 Al-0.025C（wt.%） was investigated. Following solution ...

Effects of austempering time on microstructure and tribological behaviors of 8Cr4Mo4V steel

摘要：8Cr4Mo4V bearing steel has been widely used in the industrial applications due to its exceptional mechanical properties. To further improve the tribological properties, the microstructure of 8Cr4Mo4V ...

Optimization of multi-process parameters in secondary cooling solidification process of S30432 continuous casting billet

摘要：The synergistic mechanism of multiple process parameters on the solidification structure of niobium containing austenitic stainless steel during continuous casting is complex, which seriously affects ...

Effect of Nb,Ti introduction sequence on adsorption of Nb on TiB₂ surface and grain refinement performance of Al-4Ti-1Nb-1B

摘要：In recent years, Al-Ti-Nb-B grain refiners have attracted increasing attention due to their grain refinement performance and anti-Si poisoning ability. This study investigates the influence of the int...

Intelligent design of cooling systems for aluminum alloy die-casting dies: A framework integrating topology optimization and particle swarm optimization

摘要：With the growing demand for lightweight and high-performance components in automotive and aerospace industries, aluminum alloy die-castings are evolving toward larger dimensions and thinner walls, pos...

Regulating creep behavior via dynamic in-situ precipitation of Ti₃AlC phase in Ti45Al8Nb-0.6C alloy

摘要：TiAl alloys are attractive for high-temperature structural applications, yet their creep resistance and microstructural stability at high temperatures remain critical challenges. In this study, Ti45 A...

Effect of Sc on stress-strain and hot tearing susceptibility of Al-Cu intercrystalline liquid film

摘要：Al-Cu alloys exhibit promising industrial applications owing to their low density and superior mechanical properties. However, their widespread adoption is severely limited by high hot tearing suscept...

Factors infuencing high-temperature compressive strength of alkaline phenolic resin-bonded sand

摘要：During the casting process, no-bake resin-bonded sand molds and cores rapidly heat up upon contact with high-temperature molten metal, causing dramatic changes in the resin binder system and a signifi...

Microstructure and mechanical properties evolution of near-β alloy Ti-4Al-6Cr-5Mo-5Nb-xTa

摘要：To meet the aerospace industry's demand for aircraft featuring high thrust-to-weight ratios and lightweight structures capable of operating in complex service environments, β titanium alloys with high...

Control of fine grain structures and strengthening-toughening mechanisms in magnesium alloys fabricated by wire-arc directed energy deposition

摘要：Wire-arc directed energy deposition（WA-DED） has attracted considerable attention for the fabrication of magnesium（Mg） alloys due to its high efficiency, low cost, and rapid prototyping capability for ...

Numerical simulation on macrosegregation of ingots with dynamic shrinkage porosity and dendrite microstructure

摘要：Macrosegregation and shrinkage porosity are common and interrelated defects that occur during ingot solidification. Existing models typically simulate these phenomena separately rather than in a coupl...

Achieving optimal strength-conductivity balance in cast Al-2.3Fe-Mg-Si alloys via Mg/Si ratio regulation

摘要：The Al-2.3 Fe eutectic alloy is regarded as a promising substitute for Cu conductors in automotive motors owing to its excellent castability and low resistivity. However, its application is restricted...

Enhancing forming quality, refining grains, and reducing anisotropy of mechanical properties of WAAM-processed AZ31 alloy by welding torch wobbling

摘要：The arc oscillation has a significant influence on the forming quality and mechanical properties of wire arc additive manufacturing(WAAM) process of magnesium alloy. In order to enhance the forming qu...

Process mechanisms for precision control in grayscale printing of additively manufactured sand molds

摘要：In purpose of solving the problem of precision deviation caused by droplet penetration in porous media during binder-jet printing of sand molds, the influence of process parameters such as sand mold p...

Influence of seed and crucible rotation on surface morphology during solution growth of 6-inch 4° off-axis SiC

摘要：The off-axis growth of SiC on C-face is strongly governed by seed or crucible rotation modes, exhibiting a specific surface step pattern. For unidirectional seed rotation, a macroscopic vortex-like pa...

A review on approaches to evaluate quality of molten aluminum alloys

摘要：The performance and integrity of final Al castings are intrinsically governed by the quality of the molten metal, with hydrogen content and inclusions being the two most critical yet challenging param...

Deformation behavior of as-cast Ni-based superalloy under wide temperature range with low strain rates

摘要：The mechanical behavior of superalloys during cooling is crucial for understanding crack formation in casting. Tensile tests with different strain rates were conducted on as-cast nickel-based superall...

　　相关科技期刊推荐

　　核心期刊推荐

查看更多科技期刊